Lorem Ipsum dolor sit amet
Lorem ipsum dolor sit amet, consetetur sadipscing elitr, sed diam nonumy eirmod tempor invidunt ut labore et dolore magna aliquyam erat, sed diam voluptua. At vero eos et accusam et justo duo dolores et ea rebum. Stet clita kasd gubergren, no sea takimata sanctus est Lorem ipsum dolor sit amet. Lorem ipsum dolor sit amet, consetetur sadipscing elitr, sed diam nonumy eirmod tempor invidunt ut labore et dolore magna aliquyam erat, sed diam voluptua. At vero eos et accusam et justo duo dolores et ea rebum. Stet clita kasd gubergren, no sea takimata sanctus est Lorem ipsum dolor sit amet.
Plug & play engine management · rusEFIPECU M50for BMW M50 without Vanos6× sequential6× coil-on-plugTFSI coil readyLambda controller on boardDBW ready3 bar MAP sensorOLED display Replaces the Bosch Motronic M3.1 of the BMW M50B20 and M50B25 (without Vanos). Plugs straight into the original 88-pin engine harness, no cutting and no re-pinning. More possibilities through a technology upgrade Fully programmableAdjust every map for fuel, ignition, idle and warm-up directly in TunerStudio. No chip, no EPROM, no locks. Turbo and supercharger readyBuilt-in 3 bar MAP sensor, boost control and speed density. The air flow meter is no longer needed. Integrated wideband lambdaWideband lambda control across the whole load range instead of only around lambda 1. Set up for the Bosch LSU 4.9 from the factory, no external controller needed. Retrofit electronic throttle (DBW ready)The driver for an electronic throttle body is already on board. Converting to drive-by-wire needs no additional control unit. Motorsport functionsLaunch control, flat shift, freely adjustable rev limiter, map switching and flex fuel. View and log dataLive data in TunerStudio, data logging to microSD card and engine data on the OLED display. Open and expandableOpen-source rusEFI firmware with regular updates, Lua scripting and free inputs and outputs for your own extensions. Stock DMEPECU M50Tuningfixed maps, chip tuning only✓ free in TunerStudio, change any timeLoad sensingAir flow meter✓ Alpha-N or MAP up to approx. 3 bar boostLambdaNarrowband sensor✓ Wideband, lambda controller on boardKnock controlnone, no knock sensor fitted✓ Knock sensor input, knock sensor can be retrofittedIgnition coilsoriginal coils only✓ Original coils, or modern pencil coils with built-in driver (e.g. TFSI) via 6 additional logic outputsThrottlemechanical, cable operated✓ Cable, or electronic throttle (drive-by-wire) as a retrofitForced inductionnot intended✓ Boost control, boost by gearFuelpetrol only✓ Flex fuel: ethanol sensor can be retrofitted, fuel and ignition adapt automatically (E0 to E85)Mapsone fixed calibration✓ Additional maps for ignition, VE, boost and target lambda, switchable by switch or sensorData loggingnone✓ microSD card and live data via USBInputs and outputsfixed assignment✓ freely assignable, e.g. for boost control, fan or shift lightExpansionnone✓ via CAN bus: displays, data loggers, add-on modulesUpdatesnone✓ regular rusEFI releases Fits EngineM50B20, M50B25 without Vanos VehiclesE34 520i/525i, E36 320i/325i up to approx. 09/1992 Original DMEBosch Motronic M3.1, 88-pin Replacement for these ECUs0 261 200 4000 261 200 4020 261 200 4030 261 200 4050 261 200 412Your number is missing? Ask us via the contact form. Not for the M50 with Vanos (Motronic M3.3.1): use the PECU M50B25TU for that engine. The connectors are the same, the pinout is not. Technical data PlatformuaEFI module (rusEFI), 32-bit, open-source firmwareInjection6 sequential outputs for the high-impedance stock injectors, 2 more outputs availableIgnition6 ignition drivers for the original BMW coils, plus 6 logic outputs on the auxiliary connector for coils with built-in driver (e.g. TFSI pencil coils) or external ignitersCrank/camStock crank and cam sensors; 2 VR and 3 Hall inputsLoad sensingAlpha-N from the factory, speed density possible with the MAP sensorMAP sensorKD4400AP, 20–400 kPa absolute, turbo capable up to approx. 3 barWideband lambdaLambda controller on board, set up for Bosch LSU 4.9 from the factoryDrive-by-wireDBW ready: H-bridge for an electronic throttle body on the auxiliary connectorKnock sensor1 input, software knock detectionSwitched outputs4 low-side, 2 relay outputs, 2 H-bridges (drive-by-wire, stepper motor)CommunicationUSB (TunerStudio, rusEFI Console, firmware update), CAN 500 kbit/s on the auxiliary connectorData loggingmicroSD card, inserted on deliverySupply voltage9–16 VSoftwareTunerStudio MS, rusEFI Console Three assemblies in one housing 1Carrier boardOriginal connector, ignition drivers, main relay, protection circuitry and auxiliary connectors. The pinout is hard-wired and already set in the base calibration. 2uaEFI moduleUnmodified uaEFI board from the rusEFI project, plugged in and replaceable. Firmware updates as with any uaEFI. 3CAN extension with OLEDShows engine data and messages on an OLED display and handles vehicle functions. Vehicle functions on the carrier boardIdle control via the stock idle valveA/C compressor via the CAN extensionVehicle speed from the instrument cluster Scope of deliveryPECU M50 in a RAL 4008 signal violet housing with type plateMating connectors for the auxiliary ports with crimp contactsmicroSD card, already insertedBase calibration that starts the engine, on the unit and as an .msq fileBosch LSU 4.9 with weld-in bung, harnesses and sensors are available as accessories.DownloadsManual (PDF)Getting Started (PDF)Base calibration Alpha-N (.msq)Base calibration MAP (.msq)The .msq files are for rusEFI release_20260812. German versions and more files on the download page.All downloads → Please note before buyingThe base calibration is a starting point. Every engine must be tuned individually by a competent person.Automatic gearboxes are not supported at the moment.The factory immobiliser is not needed. Ask us if your vehicle has any special features.If your vehicle differs from stock (harness, sensors, conversions), contact us before installation.For test and motorsport use only. Not road legal in Germany (StVZO) without approval.
rusEFI Open-Source Engine Management PECU M52 – uaEFI Plug & Play for the BMW M52 The PECU M52 (uaEFI Plug & Play) replaces the original Siemens MS41 engine control unit of your BMW M52 inline six with a fully programmable standalone ECU based on the rusEFI open-source platform. An unmodified uaEFI board plugs in as a module on an adapter board with the original BMW connector. Plug in, tune, drive: no cutting wires, no repinning. Ideal for turbo and supercharger conversions, motorsport and naturally aspirated tuning. 6× Injection Sequential 6× Ignition BMW coil-on-plug LSU 4.9 Wideband On-board VANOS Camshaft Closed loop P&P OEM connector No repinning CAN Communication + SD logging Technical Capabilities Fuel Injection & Ignition 6 sequential injector outputs For the stock high-impedance M52 injectors 6 ignition outputs with on-board IGBT drivers For the original BMW coil-on-plug ignition coils Start-ready base calibration for the M52 Trigger & Sensor Inputs 60-2 crank trigger and cam signal 2 VR and 3 Hall sensor inputs 9 + 2 analog inputs Flex Fuel sensor input Knock sensor input Integrated digital barometric pressure sensor Engine & Boost Control VANOS control via rusEFI variable cam timing Two DC motor drivers up to 6 A Electronic throttle body / DBW Electronic wastegate control Boost control, launch control, flat shift Communication & Logging USB communication CAN bus communication Up to two CAN interfaces On-board SD card data logging TunerStudio compatible rusEFI Console support LSU 4.9 WIDEBAND Integrated Wideband Lambda Controller The uaEFI includes an on-board wideband controller for the Bosch LSU 4.9. No separate external controller is required. Lambda data is available directly to the ECU for monitoring, tuning and closed-loop fuel control. Connecting to the BMW M52 The Plug & Play M52 connects directly to the original engine harness. The adapter board routes the vehicle signals to the uaEFI module. 1 OEM Vehicle Connector Plug & Play Plugs directly into the original M52 engine harness Injection, ignition, trigger and engine sensors via the OEM connector No cutting, no repinning, fully reversible 2 uaEFI Module Plug-in module Unmodified uaEFI board on the M52 adapter board Replaceable and reusable in other projects Firmware updates just like any uaEFI 3 Lambda Sensor LSU 4.9 6 Pins E1 – Heater + E2 – CalR E3 – Heater − E4 – Vs E5 – Ip E6 – Vs / Ip Open Official uaEFI Pinout → The OEM connector pin assignment is already handled by the adapter board. Expansion Options MAP On-board MAP Sensor 3 bar, KD4400AP already installed. BT Bluetooth Optional JDY-33 module for wireless communication. EGT Exhaust Temperature Optional MAX31855 based EGT input. CAN 2 Second CAN Bus Optional second CAN interface. rusEFI OPEN-SOURCE FIRMWARE Powerful & Flexible Software The uaEFI runs the continuously developed rusEFI engine management firmware. Configuration and tuning are done with TunerStudio and the rusEFI Console. Functions include fuel and ignition control, boost control, electronic throttle control, idle control, VANOS/VVT, Flex Fuel, CAN communication, Lua scripting, engine protection and extensive data logging. No license fees, no locks. Installation & Getting Started Official rusEFI documentation for configuration, firmware installation, first start and diagnostics. Getting Started → ECU uaEFI Documentation Specifications & hardware information PINOUT Interactive Pinout Connector & pin assignments START Getting Started From installation to first start Technical Support & Documentation Firmware Installation Firmware updates, installation and recovery. Open Firmware Guide → Trigger Configuration Crank and cam signals, synchronization and setup. Open Trigger Guide → Wideband Lambda LSU 4.9 wiring, configuration and operation. Open Wideband Guide → Diagnostics & Logging Data logging, diagnostics and troubleshooting. Open Diagnostics Guide → ! Important Installation Information The included base calibration is a starting point. Every engine must be tuned individually by a qualified person. Fits the M52 with Siemens MS41 only. Not suitable for the M52TU with MS42. Before installation, check your vehicle for deviations from stock (harness, sensors, modifications). Non-standard wiring can damage the ECU or connected components. Immobilizer (EWS): Before installation, clarify whether the EWS needs to be disabled. We are happy to advise you. Wideband control requires a Bosch LSU 4.9 sensor (not included). Operating a programmable ECU may affect your vehicle's road approval and emissions. This device is intended for motorsport and off-road use only. Official rusEFI Project Firmware, documentation and additional technical information are available from the official rusEFI project. Visit rusEFI.com →