Skip to main content Skip to search Skip to main navigation
Worldwide shipping
Buy direct from the manufacturer
Do it yourself tuning
Video-Tutorials
Own Knowledge Database

Product information "PECU BMW M50"

Plug & play engine management · rusEFI
PECU M50
for BMW M50 without Vanos
6× sequential6× coil-on-plugTFSI coil readyLambda controller on boardDBW ready3 bar MAP sensorOLED display

Replaces the Bosch Motronic M3.1 of the BMW M50B20 and M50B25 (without Vanos). Plugs straight into the original 88-pin engine harness, no cutting and no re-pinning.

More possibilities through a technology upgrade

Fully programmable
Adjust every map for fuel, ignition, idle and warm-up directly in TunerStudio. No chip, no EPROM, no locks.
Turbo and supercharger ready
Built-in 3 bar MAP sensor, boost control and speed density. The air flow meter is no longer needed.
Integrated wideband lambda
Wideband lambda control across the whole load range instead of only around lambda 1. Set up for the Bosch LSU 4.9 from the factory, no external controller needed.
Retrofit electronic throttle (DBW ready)
The driver for an electronic throttle body is already on board. Converting to drive-by-wire needs no additional control unit.
Motorsport functions
Launch control, flat shift, freely adjustable rev limiter, map switching and flex fuel.
View and log data
Live data in TunerStudio, data logging to microSD card and engine data on the OLED display.
Open and expandable
Open-source rusEFI firmware with regular updates, Lua scripting and free inputs and outputs for your own extensions.
Stock DMEPECU M50
Tuningfixed maps, chip tuning only✓ free in TunerStudio, change any time
Load sensingAir flow meter✓ Alpha-N or MAP up to approx. 3 bar boost
LambdaNarrowband sensor✓ Wideband, lambda controller on board
Knock controlnone, no knock sensor fitted✓ Knock sensor input, knock sensor can be retrofitted
Ignition coilsoriginal coils only✓ Original coils, or modern pencil coils with built-in driver (e.g. TFSI) via 6 additional logic outputs
Throttlemechanical, cable operated✓ Cable, or electronic throttle (drive-by-wire) as a retrofit
Forced inductionnot intended✓ Boost control, boost by gear
Fuelpetrol only✓ Flex fuel: ethanol sensor can be retrofitted, fuel and ignition adapt automatically (E0 to E85)
Mapsone fixed calibration✓ Additional maps for ignition, VE, boost and target lambda, switchable by switch or sensor
Data loggingnone✓ microSD card and live data via USB
Inputs and outputsfixed assignment✓ freely assignable, e.g. for boost control, fan or shift light
Expansionnone✓ via CAN bus: displays, data loggers, add-on modules
Updatesnone✓ regular rusEFI releases

Fits

EngineM50B20, M50B25 without Vanos
VehiclesE34 520i/525i, E36 320i/325i up to approx. 09/1992
Original DMEBosch Motronic M3.1, 88-pin
Replacement for these ECUs
0 261 200 4000 261 200 4020 261 200 4030 261 200 4050 261 200 412
Your number is missing? Ask us via the contact form.
Not for the M50 with Vanos (Motronic M3.3.1): use the PECU M50B25TU for that engine. The connectors are the same, the pinout is not.

Technical data

PlatformuaEFI module (rusEFI), 32-bit, open-source firmware
Injection6 sequential outputs for the high-impedance stock injectors, 2 more outputs available
Ignition6 ignition drivers for the original BMW coils, plus 6 logic outputs on the auxiliary connector for coils with built-in driver (e.g. TFSI pencil coils) or external igniters
Crank/camStock crank and cam sensors; 2 VR and 3 Hall inputs
Load sensingAlpha-N from the factory, speed density possible with the MAP sensor
MAP sensorKD4400AP, 20–400 kPa absolute, turbo capable up to approx. 3 bar
Wideband lambdaLambda controller on board, set up for Bosch LSU 4.9 from the factory
Drive-by-wireDBW ready: H-bridge for an electronic throttle body on the auxiliary connector
Knock sensor1 input, software knock detection
Switched outputs4 low-side, 2 relay outputs, 2 H-bridges (drive-by-wire, stepper motor)
CommunicationUSB (TunerStudio, rusEFI Console, firmware update), CAN 500 kbit/s on the auxiliary connector
Data loggingmicroSD card, inserted on delivery
Supply voltage9–16 V
SoftwareTunerStudio MS, rusEFI Console

Three assemblies in one housing

1
Carrier board
Original connector, ignition drivers, main relay, protection circuitry and auxiliary connectors. The pinout is hard-wired and already set in the base calibration.
2
uaEFI module
Unmodified uaEFI board from the rusEFI project, plugged in and replaceable. Firmware updates as with any uaEFI.
3
CAN extension with OLED
Shows engine data and messages on an OLED display and handles vehicle functions.
Vehicle functions on the carrier board
  • Idle control via the stock idle valve
  • A/C compressor via the CAN extension
  • Vehicle speed from the instrument cluster

Scope of delivery

  • PECU M50 in a RAL 4008 signal violet housing with type plate
  • Mating connectors for the auxiliary ports with crimp contacts
  • microSD card, already inserted
  • Base calibration that starts the engine, on the unit and as an .msq file
Bosch LSU 4.9 with weld-in bung, harnesses and sensors are available as accessories.

Downloads

The .msq files are for rusEFI release_20260812. German versions and more files on the download page.

All downloads →
Please note before buying
  • The base calibration is a starting point. Every engine must be tuned individually by a competent person.
  • Automatic gearboxes are not supported at the moment.
  • The factory immobiliser is not needed. Ask us if your vehicle has any special features.
  • If your vehicle differs from stock (harness, sensors, conversions), contact us before installation.
  • For test and motorsport use only. Not road legal in Germany (StVZO) without approval.